Airtac magnetic coupling rodless cylinder RMT structure principle and stroke table

Introduction of Airtac rodless cylinder RMT (guide rod type)

The device adopts a magnetic coupling rodless cylinder design, and there is no mechanical connection between the piston and the slider. Therefore, the airtightness of Airtac cylinder RMT will be more excellent. The movement of the piston is transmitted to the external slider through the magnetic coupling force, so that the piston rod is not needed. In terms of installation, this RMT series occupies less space than other ordinary cylinders, and the maximum stroke is also larger than that of ordinary cylinders.

Airtac rodless cylinder RMT series are equipped with fixed buffer devices at both ends, which can realize smooth reversing action without impact, and avoid accidental mechanical damage. The equipment can be equipped with an external hydraulic buffer for better buffering effect. The piston cavity and the slider of the magnetic coupling rodless cylinder are designed to be separated, which can prevent dust and dirt from entering the system, thereby indirectly extending the service life of the equipment. The double guide rod cylinder structure can make the guide precision higher, and can bear a certain lateral or eccentric load.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

Note: Install and use!

1. Before piping, AirTAC cylinder RMT must be cleaned of debris in the pipe, and protective measures must be taken to prevent dirt and debris from entering the cylinder.

2. The media used by the equipment can only be used after being filtered by a filter element above 40μm.

3. If it is used under high temperature or installation conditions, a rodless cylinder with corresponding high temperature resistance characteristics should be selected. On the contrary, if it is under low temperature conditions, anti-freezing measures should be taken to prevent the water contained in the system from freezing.

4. When Airteck rodless cylinder is dismantled and not used again for a long time, you need to pay attention to its surface anti-rust treatment, and also install anti-clogging caps for the intake and exhaust ports, and apply on the outer wall of the cylinder Anti-rust oil.

Airtac rodless cylinder RMT model meaning

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

Airtac rodless cylinder RMT stroke table

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

Airtac rodless cylinder RMT working principle

◆Determination of load size:

The load of the rodless cylinder is determined by the theoretical holding force (theoretical thrust). Therefore, in order to ensure that the cylinder can be used normally, the load cannot exceed the theoretical holding force (theoretical thrust) of the cylinder specified in the following table.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

If the load and the center of gravity of the slider coincide, the relationship curve characteristics of the load and stroke are shown in the figure below.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

In actual use of AirTAC cylinders, the load should be as close as possible to the center of gravity of the slider. If this is not possible, the following methods should be used to determine the load size according to different usage conditions. First calculate the load correction coefficient σ value: For example, if the bore of the rodless cylinder is 25mm and the stroke is 650mm, then the maximum load size = 16kg, the corresponding allowable load size at 650mm = 10.9kg, σ = 10.9/16 = 0.68.

Note: In the use condition of Φ16-500mm(st), Φ20-500mm(st), Φ25-500mm(st), Φ32-600mm(st), Φ40-600mm(st), the value of σ is 1.

Airtac rodless cylinder RMT structure diagram

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

Airtac rodless cylinder RMT configuration instructions

◆Configuration of hydraulic buffer:

The oil pressure buffer is a consumable product. It needs to be replaced in time when the energy absorption capacity decreases. The following table is the comparison table of the oil pressure buffer model for each cylinder bore. You only need to configure the corresponding specifications of oil according to the requirements of the table below. Then replace the old oil pressure buffer with the steps shown in the figure below. The screw holes at the end of the hydraulic shock absorber are not for adjustment purposes. If you adjust randomly, it will cause oil leakage. Therefore, please use the tightening torque specified in the following table to lock the hydraulic shock absorber lock nut.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

◆Configuration of induction switch:

Only magnetic type cylinders can be equipped with induction switches, and the magnetic type magnets are arranged in the four corners of the body. The specific positions are shown in the figure below. The magnetic-attached AirTAC rodless cylinder is equipped with an induction switch mounting bracket, and at the same time, there are two sets of mounting bracket fixing holes on its left and right fixing plates. Please configure the sensor switch of the corresponding specification and model according to the following table, and then guide it into the groove of the mounting frame and adjust it to the appropriate position, then tighten the set screw.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|DeceleraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table drive gearbox reducer|Linear guide|Circuit breaker|RefrigeraAirtac magnetic coupling rodless cylinder RMT structure principle and stroke table compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

okplazas.com electromechanical mall is a professional sales agent for Airtac products. Welcome to e-mail: [email protected] for consultation, and you can also contact WeChat customer service online at+86- 13689242098 for product consultation!