Schneider universal circuit breaker Compact NS series control unit

Schneider universal circuit breaker "basic protection type" control unit

Micrologic 2.0, 5.0 and 6.0 control units protect the power supply circuit. Micrologic 5.0 and 6.0 provide time selectivity during short circuit.

◆Protection

The protection threshold and delay are adjusted with the adjusting knob.

Provide standard long delay tuning module.

●Overload protection

Real rms long delay protection.

Thermal memory: The accumulation of heat before and after the trip.

●Short circuit protection

Short time delay (rms) and instantaneous protection.

In the delay, I2t (ON or OFF) can be selected.

●Neutral line protection

There is no neutral line protection on the 3-pole Schneider universal circuit breaker.

On the 4-pole Schneider universal circuit breaker, the neutral line protection can be set through the 3-position switch: the neutral line is unprotected (4P 3d), the neutral line is half-protected 0.5In (4P 3d+N/2) or medium Full protection of sex line In (4P 4d).

◆Instructions

The overload indication is realized by the alarm LED on the panel of the universal circuit breaker control unit. The LED lights up when the current exceeds the long delay setting threshold.

◆Test

The circuit breaker can be detected through the test hole of the control unit through a handheld tester and a full-function test box.

The panel structure of the Schneider universal circuit breaker Compact NS series Micrologic "basic protection type" control unit is shown in the figure below.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|Deceleration drive gearbox reducer|Linear guide|Circuit breaker|Refrigeration compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

1. Long delay, current setting value and trip delay;

2. Overload signal (LED);

3. Short delay, current setting value and trip delay;

4. Instantaneous protection current setting;

5. Long time delay tuning module fixing screws;

6. Test hole.

Schneider universal circuit breaker "ammeter" control unit

Micrologic 2.0A, 5.0A, 6.0A control units protect the power circuit. It also provides measurement, display, and maximum current, and protection type 6 provides ground fault protection.

◆Protection settings

Use the adjustment button on the universal circuit breaker controller to set the protection threshold and delay. The current and time values ​​are displayed on the screen, and a standard long delay setting module is provided.

●Overload protection

RMS long delay protection.

Thermal storage: The accumulation of heat before and after tripping.

●Short circuit protection

Short time delay (rms) and instantaneous protection.

For short delay, I2t (ON or OFF) can be selected.

●Ground fault protection

I2t (ON or OFF) is optional.

●Neutral line protection

There is no neutral line protection on the 3-pole universal circuit breaker.

On the 4-pole universal circuit breaker, the neutral line protection can be set by the 3-position switch: the neutral line has no protection (4P 3t), the neutral line protection is 0.5In (4P, 3t+N/2), the neutral line Protect In(4P 4t).

●Zone selective interlocking (ZSI)

ZSI is connected to multiple control units to provide complete selectivity of ground fault protection and short-time delay protection, without delay before tripping.

◆ Ammeter

Schneider universal circuit breaker Micrologic control unit A measures the true effective value (RMS) of the current.

The digital screen LCD continuously displays the maximum load phase current (lmax), or by pressing the navigation key, it can also display I1, I2, I3, IN, Ig, I∆n storage current (maximum) and set it.

The external power supply option can display current of <20%In.

If the current is lower than 0.05In, the measured value is meaningless. At 0.05 to 0.2In, the accuracy is 0.5% In+1.5% of reading.

●Overload alarm

The yellow LED on the panel of the Schneider circuit breaker control unit provides an overload alarm indication.

●Fault indication

LED lights indicate the type of fault.

1. Overload (Ir);

2. Short circuit (Isd, Ii);

3. Grounding (Ig);

4. Internal failure (Ap).

●Battery

After the fault occurs, the trip indicator LED light-stays on until the test/reset button is pressed. Under normal circumstances, the battery can power the LED for about 10 years.

●Test

Small or portable test devices can detect Schneider universal circuit breakers through the panel test hole, corresponding to the Micrologic 6.0A control unit, and the ground fault protection can be tested through the test button.

The panel structure of the Schneider universal circuit breaker Compact NS series Micrologic "ammeter" control unit is shown in the figure below.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|Deceleration drive gearbox reducer|Linear guide|Circuit breaker|Refrigeration compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

1. Long delay, current setting value and trip delay;

2. Overload signal (LED);

3. Short delay, current setting value and trip delay;

4. Instantaneous value;

5. Ground fault and trip delay;

6. Ground fault test button;

7. Long delay calibration fixing screw;

8. Test hole;

9. Test light, reset and battery test;

10. Display of the cause of tripping;

11. Digital display;

12. Ammeter and three-phase bar chart;

13. Navigation keys.

Schneider universal circuit breaker "current, voltage" control unit

The Micrologic E type control unit protects the power supply circuit. It provides measurement, display, and maximum current at the same time. Protection type 6 provides ground fault protection.

◆"Power Meter" measurement

In addition to the current measurement function of the A-type control unit, the E-type control unit measures and displays:

1. Current value required;

2. Voltage value: phase to phase, relative to ground, average value, unbalance coefficient;

3. Instantaneous power value: active, reactive, and apparent;

4. Power factor: PF;

5. Required power value: P required;

6. Electricity: active, reactive, and apparent.

Active energy measurement accuracy is 2% (including transformers). The current measurement range is the same as that of Type A control unit, depending on whether there is a 24V DC external power supply module.

◆Protection

Schneider universal circuit breaker protection module and delay module are in the form of adjustable dials.

●Overload protection

Real RMS long delay protection.

Thermal memory: Heat accumulation before and after tripping.

●Short circuit protection

Short time delay (rms) and instantaneous protection.

For short delay, I2t (ON or OFF) can be selected.

●Ground fault protection

The Micrologic 6.0E type control unit of the Compact NS series universal circuit breaker has ground fault protection.

I2t is optional (ON or OFF).

●Neutral line protection

3-pole circuit breaker without neutral line protection

4-pole circuit breaker, neutral line protection can be set through the 3-position switch: neutral line protection (4P 3d), neutral line protection 0.5Ir (4P 3d+N/2), neutral line protection Ir (4P 4d) ).

●Zone Interlocking (ZSI)

ZSI is connected to multiple control units to provide complete selectivity of grounding protection and short-delay protection, and no delay is required before tripping.

◆Overload alarm

The yellow LED on the panel of the universal circuit breaker control unit provides an overload alarm indication.

◆Fault indication

LED lights indicate fault type

1. Overload (Ir);

2. Short circuit (Isd, Ii);

3. Grounding (Ig);

4. Internal failure (Ap).

◆Trip history

Schneider universal circuit breaker last 10 trip records, each trip record and display the following information:

Tripping reason Ir, Isd, Ii, Ig or self-protection Ap.

●Battery

After the fault occurs, the trip indicator LED light stays on until the test/reset button is pressed. Under normal circumstances, the battery can power the LED for about 10 years.

◆Test

Small or portable test devices can detect universal circuit breakers through the panel test holes. Corresponding to the Micrologic 6.0E control unit, the ground fault protection can be tested through the test button.

The panel structure of the Schneider universal circuit breaker Compact NS series Micrologic "current, voltage" control unit is shown in the figure below.

Transmitter|Encoder|Soft starter|Power supply|VFD|Light curtain|Servo products|Human-machine interface|Solenoid valve|Cylinder|Actuator|Flow meter|Transformer|Thyristor|Sensor|Deceleration drive gearbox reducer|Linear guide|Circuit breaker|Refrigeration compressorAll industrial products of okplazas are purchased from the original factory or formal channels of agents to ensure the original authenticity, which perfectly solves the problem of industrial product sample procurement and small-batch procurement for the majority of engineers and purchasing personnel.

1. Long delay, current setting value and trip delay;

2. Overload signal (LED);

3. Short delay, current setting value and trip delay;

4. Instantaneous value;

5. Ground fault and trip delay;

6. Ground fault test button;

7. Long time delay calibration fixing screw;

8. Test hole;

9. Test light, reset and battery test;

10. Display of the cause of tripping;

11. Digital display;

12. Ammeter and three-phase bar chart;

13. Navigation keys for quick browsing (only E-type control unit);

14. Navigation key for viewing menu content;

15. Select the menu navigation key.

Note: Schneider universal circuit breaker Micrologic E control unit is equipped with a standard lead-sealed transparent cover.

The above is the Schneider universal circuit breaker Compact NS series control unit, I hope it can help everyone. okplazas.com Motor Mall is a professional agent selling Schneider Electric products. Welcome to email: [email protected] for consultation, and you can also contact WeChat ：+86-13689242098customer service online for product consultation!