Electrical parameters

• Power supply voltage 12-24V DC
• Available supply voltage 12V DC; 24V DC
• Resolution 8P/R (3 bits)
• Output mode PNP open collector output
• Output logic positive logic (active high)
• Output code binary code
• Maximum response frequency 35KHz
• Maximum electrical rotation speed (highest response frequency/resolution) *60
• Increase when the direction of rotation CCW is reversed
• Rise/fall time≤800ns
• Allowable ripple≤5%rms
• Consumption current (when no load) ≤100mA
• Axial direction of outlet (cable outlet)
• Flange type synchronous flange
• Output voltage "H" ≥ (power supply voltage) -1.5V

Measuring range 0°~360°

Mechanical parameters

• Starting torque≤0.004N·m
• Shaft moment of inertia 4*10＾(-6)kg*m＾2
• The allowable load of the radial shaft is 98N
• Axial shaft allowable load 24.5N
• The maximum allowable rotation speed is 3000r/min (Note: This speed indicates the mechanical load limit of the encoder. If this limit is exceeded, it will have a negative impact on the service life of the bearing. In addition, the signal may also be interrupted.)

Weight about 380g

Environmental conditions

• Operating environment temperature -10℃～+70℃
• Storage environment temperature -25℃～+85℃
• Operating environment humidity 35～85%RH (no condensation)
• Withstand voltage AC750V (50/60Hz) 1 minute
• Insulation resistance ≥100MΩ
• Vibration resistance (durable) 10～55Hz 1.5mm X, Y, Z directions for 2h
• Impact resistance (durable) 50G

Protection level dust-proof and drip-proof type: IP64

Installation size

• Shaft type solid shaft
• Shaft size φ8mm
• Outer diameter φ50mm
• Pitch circle diameter (PCD) φ38mm
• Screw parameters 4*M4

Screw length (Depth) 10

EP50S8-8-2R-P-24 Rotary Encoder Shaft Outer Diameter: Ø8mm The smallest response frequency: 35kHz The smallest allowable speed: 3000rpm Starting torque: Max. 70gf.cm(max. 0.0069Nm) Resolution: 8(P/ R) Rotation direction: CCW direction output value increase Control output: PNP open collector power supply voltage: 12-24VDC ±5% (ripple PP: Max.5%) Connection cable type: Axial wiring lead type Protection level: IP64

Data sheet of EP50S8-8-2R-P-24 rotary encoder: Shaft outer diameter Ø8mm, the largest response frequency 35kHz, the largest allowable speed 3000rpm, starting torque Max. 70gf.cm(max. 0.0069Nm) resolution 8(P/R ) Output code system, binary code, rotation direction, CCW direction, output value increase, control output PNP open collector power supply voltage 12-24VDC ±5% (ripple PP: Max.5%) Connection cable type Axial wiring lead type Protection grade IP64 Certification CE Ambient temperature -10~70℃, storage: -25~85℃ Ambient humidity 35~85%RH, storage: 35~90%RH Accessory bracket, coupling weight about 482g (about 398g) ※In parallel In this case, when selecting the resolution, please make sure that the maximum response speed is lower than or equal to the maximum allowable speed [the maximum response speed (rpm)=the minimum response frequency/resolution × 60sec

※The weight includes the outer packaging, and the net weight of the product is in parentheses. ※Environmental characteristics are non-icing and dew condensation state. The working principle of the EP50S8-8-2R-P-24 rotary encoder: There are many optical channel engraved lines on the optical code disc of the Pytograph Rotary Encoder, and each engraved line is in the order of 2 lines, 4 lines, 8 lines and 16 lines. ……Arrangement, in this way, at each position of the encoder, by reading the open and dark of each engraved line, a set of binary codes from the zero power of 2 to the n-1 power of 2 is obtained. (Gray code), this is called an n-bit * encoder. Such an encoder is determined by the mechanical position of the photoelectric encoder, and it is not affected by power outages and interference. Each position determined by the mechanical position of the symmetrical rotary encoder is one-dimensional. It does not need to be memorized, does not need to find a reference point, and does not need to be counted all the time. When the position needs to be known, it is time to read its position. In this way, the anti-interference characteristics of the encoder and the reliability of the data are greatly improved. EP50S8-8-2R-P-24 Rotary Encoder Advantages: 1. Because the measured data is a * angle, and can be stored when the power is off, it can save the trouble of restoration when the power supply is restored. 2. The rotation angle is digitally output, and data will not be disordered due to interference. Related models of EP50S8-8-2R-P-24 rotary encoder: EP50S8-48-3R-P-24, EP50S8-48-3R-P-5, EP50S8-48-1F-N-24, EP50S8-48- 1F-N-5, EP50S8-48-2 FN-24, EP50S8-48-2F-N-5, EP50S8-48-3F-N-24, EP50S8-48-3F-N-5, EP50S8-48-1R -N-24, EP5 0S8-48-1R-N-5 EP50S8-48-2R-N-24, EP50S8-48-2R-N-5, EP50S8-48-3R-N-24, EP50S8-48-3R -N-5, EP50S8-40- 1F-P-24, EP50S8-40-1F-P-5, EP50S8-40-2F-P-24, EP50S8-40-2F-P-5, EP50S8-40-3F -P-24, EP 50S8-40-3F-P-5 EP50S8-40-1R-P-24, EP50S8-40-1R-P-5, EP50S8-40-2R-P-24, EP50S8-40-2R -P-5, EP50S8-40-3 RP-24, EP50S8-40-3R-P-5, EP50S8-40-1F-N-24, EP50S8-40-1F-N-5, EP50S8-40-2F- N-24, EP5 0S8-40-2F-N-5 EP50S8-40-3F-N-24, EP50S8-40-3F-N-5, EP50S8-40-1R-N-24, EP50S8-40-1R- N-5, EP50S8-40-2 RN-24, EP50S8-40-2R-N-5, EP50S8-40-3R-N-24, EP50S8-40-3R-N-5, EP50S8-32-1F-P -24, EP 50S8-32-1F-P-5 EP50S8-32-2F-P-24, EP50S8-32-2F-P-5, EP50S8-32-3F-P-24, EP50S8-32-3F-P -5, EP50S8-32-1 RP-24, EP50S8-32-1R-P-5, EP50S8-32-2R-P-24, EP50S8-32-2R-P-5, EP50S8-32-3R-P- 24, EP 50S8-32-3R-P-5 EP50S8-32-1F-N-24, EP50S8-32-1F-N-5, EP50S8-32-2F-N-24, EP50S8-32-2F-N- 5. EP50S8-32-3 FN-2 4. EP50S8-32-3F-N-5, EP50S8-32-1R-N-24, EP50S8-32-1R-N-5, EP50S8-32-2R-N-24, EP 50S8-32-2R-N -5 EP50S8-32-3R-N-24, EP50S8-32-3R-N-5, EP50S8-24-1F-P-24, EP50S8-24-1F-P-5, EP50S8-24-2 FP-24 , EP50S8-24-2F-P-5, EP50S8-24-3F-P-24, EP50S8-24-3F-P-5, EP50S8-24-1R-P-24, EP5 0S8-24-1R-P- 5